Updated Nov 21, 2026· 8 min read

Key takeaways

  • Compare the best engine oil pumps for LS and Ford Modular engines, and learn why a mechanical gauge check must come before any pump replacement.

Disclosure: As an Amazon Associate, I earn from qualifying purchases.

Our top pick: Melling 10355 Oil Pump. Runner-up: Melling 10295 Oil Pump.

A flickering oil light or a gauge sagging at idle sends many owners straight to the parts store for a new pump. Stop there. Low oil pressure is an engine-killing emergency — if the warning is real, shut the engine off and stop driving, because a few miles without lubrication can turn a repairable engine into scrap. But the pump itself is usually not the cause. Before you buy anything, screw a mechanical test gauge into the sender port and read the true pressure hot, at idle and at cruising rpm. Senders fail and dash gauges lie; a mechanical gauge does not. On modern engines, genuinely low hot pressure more often means worn main and rod bearings — excess clearance lets oil escape faster than any healthy pump can replace it. A new pump cannot restore pressure lost at the bearings. The five pumps below are for the cases where the pump, its relief valve, or its pickup really is the problem, or where the engine is already apart for a rebuild.

How to Choose

Start with the diagnosis, not the catalog. Confirm real pressure with a mechanical gauge and compare it against the factory specification for your engine at the specified rpm and oil temperature. If pressure is low, inspect the pickup before condemning the pump: the pickup screen clogs with sludge and, on many modern engines, with crumbled plastic timing chain guide debris, and a starved healthy pump reads exactly like a dead one. The pickup tube’s O-ring is another silent killer on LS engines — a hardened or pinched O-ring lets the pump suck air. Real pump failures do exist: worn gerotor or gear clearances, a scored housing, and a pressure relief valve stuck open on a piece of debris or stuck closed from varnish, which can spike pressure and blow out seals or the filter gasket.

Next, match the pump to the engine family and drive style. Front-cover-mounted gerotor pumps (LS, Ford Modular) are crank-driven and engine-specific; older small-block Chevy pumps are distributor-driven from inside the pan. Then decide volume and pressure honestly. A high-volume pump moves more oil per revolution and suits engines with looser clearances, added oil coolers, or remote filters. A high-pressure pump mostly changes the relief spring setting, raising the pressure ceiling. Neither one fixes worn bearings, and a high-volume pump on a tight stock engine can pump the pan dry at sustained high rpm and overwork the distributor drive gear on older designs. Finally, plan the job: on most cars this is a pan-off or engine-out job, the new pump must be primed or packed exactly as its maker instructs so the first start is not a dry start, and the pickup should be replaced or meticulously cleaned and fitted with a new O-ring or gasket at the same time.

The 5 Best Engine Oil Pumps

1. Melling 10355 Oil Pump — LS Standard Volume, High Pressure

Specs:
– Application: GM LS-series engines, wet sump, internal mount
– Volume/pressure: standard volume, high pressure (about 10 psi over the stock M365 pump)
– Body: hardcoat anodized housing with cast iron phosphate-coated cover
– Included: optional +20 psi pressure relief spring
– Weight: 2.5 lb; made in the USA

The 10355 is the sensible default for a stock or mildly built LS that needs a pump during a timing set or front-cover job. Standard volume keeps the oiling system behaving as GM calibrated it, while the firmer relief spring supports pressure at hot idle without the pan-draining habits of a high-volume unit. The hardcoat body and iron cover resist the wear that opens up gerotor clearances over time. It is a replacement for a tired or debris-damaged pump on a healthy engine — not a cure for pressure lost through worn bearings.

2. Melling 10295 Oil Pump — LS Standard Volume, High Pressure

Specs:
– Application: GM LS-series engines, wet sump, internal mount
– Volume/pressure: standard volume, high pressure
– Inlet: 7/8 in pickup inlet
– Included: pickup O-ring and relief spring
– Package: 10 x 10 x 6 in, about 2.7 lb

The 10295 is Melling’s other long-running LS answer, built around the larger 7/8-inch pickup inlet used by many factory truck and car applications. Like the 10355, it pairs stock displacement with a higher relief setting, which is the combination most street LS engines actually want. Confirm your pickup tube diameter before ordering — LS pickups are not all the same, and forcing the wrong pairing invites the classic sucked-air O-ring failure. On any LS pump swap, centering the pump on the crank snout during torquing matters for gerotor life; follow the maker’s sequence.

3. Melling M295HV Oil Pump — LS High Volume

Specs:
– Application: GM LS 4.8L, 5.3L and 6.0L truck and SUV engines
– Volume/pressure: high volume gerotor design
– OEM cross: M295HV (UPC 729295103585)
– Mounting: front cover, crank-driven, wet sump
– Pickup: uses the factory-style tube and O-ring (replace the O-ring)

The M295HV is the high-volume counterpart for LS truck engines, moving more oil per revolution than the standard pump. That extra volume suits a high-mileage engine with measurably wider clearances, an added oil cooler, or sustained towing heat — provided pan capacity and the pickup are up to it. It is also the pump most often bought for the wrong reason: if your 5.3L shows low hot idle pressure because the bearings are worn, the HV pump may mask the gauge reading briefly while the wear continues. Verify with a mechanical gauge, and treat a pressure drop as engine information, not a shopping list.

4. Melling M360 Oil Pump — Ford Modular High Volume

Specs:
– Application: Ford Modular engines, including the 5.4L Triton
– Volume/pressure: high volume, wet sump, internal mount
– Construction: crank-driven gerotor, front cover mounted
– Package: 8.0 x 5.5 x 6.0 in, 3.4 lb
– Origin: made in the USA

Ford Modular owners meet the oil pump during timing jobs, and the M360 is the established high-volume replacement for the 4.6L and 5.4L family. On the 5.4L 3V especially, healthy oil delivery matters because the cam phasers and timing tensioners are hydraulically fed — but be honest about cause and effect: those engines usually lose pressure and phaser control from sludge, broken guide plastic in the pickup screen, and worn components, not from a weak pump casting. Fit the M360 while the cover is off, fit a new pickup or clean the screen to bare metal, and the oiling side of the job is done properly.

5. A-Premium APOIP220 High Volume Oil Pump — LS Value Alternative

Specs:
– Application: Chevrolet Silverado, Tahoe, Camaro, Suburban; GMC Sierra, Yukon, Savana; Cadillac models with 4.8L, 5.3L or 6.0L LS engines
– Volume/pressure: high volume
– Manufacturer part number: APOIP220
– OEM cross: M295HV
– Mounting: front cover, crank-driven, wet sump

The A-Premium pump targets the same LS truck applications as the M295HV and crosses directly to that part number, making it the budget-route entry on this list. The honest framing: an oil pump is an engine-critical part with no roadside workaround, and the established brands publish their testing standards while value brands generally do not. If you choose this route, inspect the casting, check gerotor smoothness by hand, prime it exactly as instructed, and verify hot pressure with a mechanical gauge on the first run.

Usage and Buying Notes

Prime every new pump the way its maker specifies — packing a gear pump with assembly lube, or pre-filling a gerotor pump with oil — because a dry pump may never pull oil up from the pan on cranking alone. On distributor-driven engines, use a priming tool on a drill and watch for oil at the rocker arms before the first start. Replace the pickup screen or clean it to bare metal, always fit a new pickup O-ring or gasket, and torque the pickup bolts to spec; an air leak on the suction side mimics a failed pump perfectly. After the first start, verify hot idle and cruise pressure with the mechanical gauge again and write the numbers down as your baseline. Change the oil and filter after the job: whatever debris killed the old pump is still circulating. And remember the scope — on most modern cars the pan will not clear the crossmember, so this is an engine-out or engine-raised job, and a professional diagnosis first is cheaper than a pump plus the engine work it did not fix.

FAQ

Can a new oil pump fix low oil pressure?
Only if the pump, its relief valve, or its pickup is actually the fault. Low pressure caused by worn bearings, a clogged pickup screen, or a leaking pickup O-ring will not be fixed by a pump alone, which is why a mechanical gauge reading and a pickup inspection come first.

What is the difference between high-volume and high-pressure pumps?
A high-volume pump moves more oil per revolution, suiting looser clearances or added coolers. A high-pressure pump mainly uses a stiffer relief spring to raise the pressure ceiling. They solve different problems, and neither repairs a worn engine.

What are the signs the oil pump itself has failed?
Verified low pressure on a mechanical gauge with a clean pickup, pressure that vanishes as oil thins when hot, a relief valve stuck open or closed, and visible scoring or excess clearance in the gears or gerotor during inspection. A warning light alone is not proof — senders fail often.

Should I replace the pickup tube with the pump?
Yes, or remove and clean it until the screen is bare metal, and always fit a new O-ring or gasket. Sludge and timing guide debris in the screen starve healthy pumps, and a hardened O-ring lets the pump draw air instead of oil.

Is replacing an oil pump a DIY job?
On most modern vehicles it is advanced work: the pan usually cannot come off with the engine in place, and front-cover pumps require timing component removal. Experienced builders do it routinely; first-timers should budget for professional help.

Conclusion

The best engine oil pump is the one matched to your engine family, your clearances, and a verified diagnosis. The Melling 10355 and 10295 cover stock LS replacements, the M295HV and A-Premium APOIP220 serve high-volume LS truck needs at two quality tiers, and the M360 does the same job for Ford Modular engines. Buy the gauge before the pump, inspect the pickup before blaming the casting, prime the new pump before the first start — and if the gauge says the bearings are gone, believe it.

A
Autozane Editorial Team
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.
Best Engine Oil Pumps: 5 Picks After You…Check price on Amazon

More from Amazon

Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.

Amazon Prime

Free shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.

Start a Prime free trial
Audible

Audiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.

Try Audible free
Amazon Music Unlimited

Ad-free music streaming. Eligible new subscribers can start with a free trial.

Try Music Unlimited free
Amazon Business

A free business account with business pricing and bulk-buying tools for work, shop or home office.

Create a business account

As an Amazon Associate we earn from qualifying purchases.