Key takeaways
- AA Ignition MAF sensor review for GM trucks and SUVs: fitment, interchange part numbers, failure symptoms, and who should buy this replacement sensor.
The AA Ignition Mass Air Flow (MAF) Sensor is a direct-replacement sensor for General Motors full-size trucks and SUVs built between 1999 and 2009. It replaces the original Delphi AF10043 sensor and the GM part numbers 25168491 and 25318411, fitting the Silverado, Tahoe, Sierra, Yukon, Escalade, and other listed GM models. A mass air flow sensor measures the air entering the engine so the engine control unit can set the correct fuel mixture, and when it fails the symptoms are hard to miss: rough idling, hesitation, poor fuel economy, and a check engine light.
This review covers what the sensor is, which vehicles it fits, how it compares with the alternatives, and who should buy it. Anything the listing does not publish is marked not stated rather than guessed.
As an Amazon Associate, we earn from qualifying purchases.
Quick Answer
The AA Ignition MAF sensor is a straightforward direct replacement for GM trucks and SUVs from 1999 to 2009 that use the Delphi AF10043 sensor. It suits owners whose original sensor has failed and who want an aftermarket part that matches the original connector and housing. Confirm the part numbers 25168491, AF10043, or 25318411 against the sensor already in the vehicle before ordering.
Key Specs
| Spec | Detail |
|---|---|
| Brand | AA Ignition |
| Product type | Mass air flow (MAF) sensor, complete assembly with housing |
| Replaces (interchange) | Delphi AF10043; GM 25168491, 25318411, 213-4160, 213-364; ACDelco 19330121; Standard Motor Products MAS0203 |
| Compatible vehicles | GM full-size trucks and SUVs, model years 1999–2009 (see fitment list below) |
| Engines covered | 4.3L V6; 4.8L, 5.3L, 5.7L, 6.0L, and 8.1L V8, depending on model |
| Connector | 5-blade terminal, as specified for the OE sensor it replaces |
| Signal output | Frequency, as specified for the OE sensor it replaces |
| Mounting | Bolt-on, matching the OE mounting |
| Intake air temperature sensor | Not stated |
| Dimensions | Not stated |
| Weight | Not stated |
| Model number | Not stated |
| UPC | Not stated |
| Warranty | Not stated |
| Country of origin | Not stated |
The published fitment list covers the Buick Rainier (2004–2007); Cadillac CTS, DeVille, Eldorado, Escalade, and Seville (2000–2006); Chevrolet Avalanche, Corvette, Silverado 1500/2500/3500, SSR, Suburban, Tahoe, and Trailblazer (1999–2009); GMC Envoy, Sierra 1500/2500/3500, Yukon and Yukon Denali, and Hummer H2; Isuzu Ascender; Oldsmobile Aurora; Pontiac Bonneville and GTO; and Saab 9-7X. Year ranges vary by model and engine, so the part numbers on the old sensor are the final check, not the model year alone.
One sourcing note matters here. No direct ASIN-field snippet for this ASIN surfaced in public search results, so the fitment above rests on the published AA Ignition listing identity as reproduced by independent retailers and buying guides. The listing title, the brand, and the interchange numbers all line up, but confirm the part numbers on the Amazon listing before ordering.
Who It’s For
This sensor is for owners of a listed GM truck or SUV whose original MAF sensor has failed or is sending bad readings.
It suits do-it-yourself owners as well. The sensor sits in the intake tract between the air filter housing and the throttle body, held by bolts with a single electrical connector, so the swap itself is a basic job with hand tools.
Who Should Skip It
Skip this sensor if the vehicle is not on the fitment list above. Also skip it if the old sensor carries a different part number: match 25168491, AF10043, or 25318411 exactly, and do not assume a match from the model name alone.
Skip it too if the goal is an original-equipment branded part. This is an aftermarket replacement made by AA Ignition, not a genuine GM or Delphi part, and the listing says so plainly. Finally, do not buy a sensor before diagnosing the problem.
How It Compares with Typical Alternatives
The main alternative is an original-equipment sensor from Delphi or GM. OE sensors are the calibration benchmark for the vehicles they were built for, and they are the default choice when exact calibration matters most. Aftermarket direct replacements like this AA Ignition sensor are built to the same form, fit, and function as the OE part, with the same connector and housing, and they exist to give owners a lower-cost route to a working sensor.
A second alternative is a sensor-only probe, which replaces just the sensing element. This AA Ignition sensor is a complete assembly, so the housing comes with it and there is no need to separate the element from the old tube.
A third option is a remanufactured sensor, which reuses a returned housing and electronics after testing. Whichever route is chosen, the deciding factors are the same: the correct OE part number, the correct connector, and a housing that matches the intake tract.
Frequently Asked Questions
How do I know if my MAF sensor is bad?
The usual signs are a check engine light, rough or surging idle, hesitation or jerking under acceleration, stalling, and worse fuel economy. A scan tool often shows a MAF trouble code in the P0100 to P0104 range.
Will this sensor fit my Silverado, Tahoe, or Sierra?
It fits the models and years in the fitment list above, but the reliable check is the part number on the sensor already in the vehicle. If it reads 25168491, AF10043, or 25318411, this sensor is the matching replacement. If it reads a different number, use the listing’s fitment check with the exact year, model, and engine instead of guessing.
Can I clean the old sensor instead of replacing it?
Sometimes. Dirt and oil film on the sensing element can distort readings, and a cleaner made specifically for MAF sensors can restore it. Use only a dedicated MAF sensor cleaner, never brake cleaner, solvents, or compressed air, which can destroy the sensing element. Cleaning helps a dirty sensor, not a dead one: if the element has failed electrically, replacement is the only fix.
Is installing a MAF sensor a DIY job?
For most owners of these trucks, yes. The sensor sits between the air filter housing and the throttle body. The usual steps are to disconnect the negative battery terminal, unplug the electrical connector, unbolt the sensor, and install the new one in reverse order.
Final Verdict
The AA Ignition MAF sensor is a practical direct replacement for the listed GM trucks and SUVs from 1999 to 2009. It matches the OE sensor it replaces on part numbers, connector, and housing, and it is built for owners who need a failed sensor fixed without chasing a dealer part.
The verdict comes with two conditions. First, match the part numbers 25168491, AF10043, or 25318411 on the old sensor. Second, note the sourcing caveat in the specs section — the fitment here rests on the published AA Ignition listing identity rather than a direct ASIN-field snippet, so confirm the listing details before ordering. With those checks done, this is a sensible pick for a failed MAF sensor on a listed GM vehicle.
More from Amazon
Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.
Free shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.
Start a Prime free trialAudiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.
Try Audible freeAd-free music streaming. Eligible new subscribers can start with a free trial.
Try Music Unlimited freeA free business account with business pricing and bulk-buying tools for work, shop or home office.
Create a business accountAs an Amazon Associate we earn from qualifying purchases.