Updated Nov 21, 2026· 9 min read

Key takeaways

  • Compare the best engine stands for a home garage, with 1,000 to 1,500 lb capacities, rotating heads, folding frames and caster layouts explained.

Pulling an engine is only half the job. Once the block is out it needs a secure, mobile mount that lets you rotate it to reach the oil pan, the rear main seal and every bolt in between. The five stands below span 1,000 to 1,500 pounds of stated capacity, from a compact stand for four-cylinder work to folding frames built for dressed V8 engines.

Our top pick: BIG RED AT26801UR Torin Steel Rotating Engine Stand, 3/4 Ton (1,500 lb), Blue. Runner-up: BIG RED TAM25671-2 Torin Steel Rotating Engine Stand, 5/8 Ton (1,250 lb), Red.

As an Amazon Associate, we earn from qualifying purchases.

Quick answer

For most home rebuilds, the BIG RED AT26801UR is the safest default: a 1,500 lb rating, a folding frame and five casters. The TAM25671-2 adds a tool tray at 1,250 lb, the ZLWBHBS matches it with five swivel casters, the W41025 is the lightest option at 1,000 lb, and the VEVOR 1300 adds a U-shaped base at 1,300 lb.

BIG RED AT26801UR Torin Steel Rotating Engine Stand, 3/4 Ton (1,500 lb), Blue

The AT26801UR is the heavy-duty anchor of this group, rated by Torin at 3/4 ton, or 1,500 lb. That rating puts dressed small-block and big-block V8 engines, most V6 engines and many inline sixes within its stated working range, with headroom left for accessories still bolted to the block. It is the only stand here rated for the heaviest engines a home garage normally handles. The mounting head rotates a full 360 degrees and carries four adjustable arms, so the plate can be aligned to a wide spread of bellhousing bolt patterns.

Stability comes from an extra-wide H-shaped base rather than a single front leg, which spreads the load across a broader footprint when the engine is rotated sideways. The frame rolls on five casters, two fixed and three that swivel, and it folds once the engine is off, a real advantage where floor space is shared with a daily driver. Assembled, the stand measures 33.5 by 29.5 by 35.4 inches, and at over 75 lb it is the heaviest stand here: planted under a heavy block, but the one you will least want to carry rather than roll.

BIG RED TAM25671-2 Torin Steel Rotating Engine Stand, 5/8 Ton (1,250 lb), Red

The TAM25671-2 steps down to a 5/8 ton rating of 1,250 lb, which still covers the majority of passenger-car engines a home mechanic is likely to pull, including most dressed small-block V8 engines. Its mounting head adjusts and rotates 360 degrees, and four adjustable arms handle the bellhousing pattern matching that any rebuild starts with. For engines that live in the middle of the weight range, that rating leaves useful headroom without paying for capacity that never gets used.

The detail that separates this model from its bigger sibling is the built-in tool storage tray. Fasteners, plugs and hand tools stay on the stand, at working height, instead of scattering across the concrete and getting hunted for mid-job. The trade-off is that the frame does not fold, so it keeps its full footprint in storage. That footprint is 39.17 by 27.76 by 37.8 inches, noticeably longer than the folding AT26801UR, and the stand weighs 60.5 lb. In practice this is the pick for a garage with a dedicated work corner, where the stand can live assembled and ready, and where the tray earns its keep on every teardown.

ZLWBHBS 1250 lbs Engine Stand, Red

The ZLWBHBS stand, model QC-5872, matches the Torin mid-range rating with a stated maximum load of 1,250 lb, or 567 kg. It is built from A3 steel with cast iron in the rotating hardware, and its mounting head turns 360 degrees on four adjustable metal arms, following the same basic layout as the branded stands here. That puts it in the same working class as the branded 1,250 lb stands.

Where it differs is underneath. All five of its casters swivel, and the caster wheels are cast iron rather than plastic or plain steel, which suits rough or cracked concrete where small hard wheels can chip or hang up on edges. A stand that can be nudged in any direction is useful when a loaded engine needs to be threaded between a bench and a car. The H-frame folds for storage, the footprint is 33.07 by 33.07 inches, and the two base widths are listed at 25.59 inches and 16.53 inches. Gross weight is 46.3 lb, making it the lightest of the folding options here. For buyers comparing on mobility and storage rather than brand history, this is the configuration to look at.

Performance Tool W41025 Rotating Vehicle Engine Block Stand, 1/2 Ton (1,000 lb), Yellow

The W41025 is the lightest stand in this guide at about 30 lb, and that single figure shapes everything about it. Rated at 1/2 ton, or 1,000 lb, it is aimed at four-cylinder and V6 engines and bare V8 blocks rather than fully dressed heavy engines. The rotating head locks in six positions instead of stopping wherever friction leaves it, for a repeatable, positive lock.

Construction is heavy-gauge tubular steel, and the assembled dimensions are compact at 30-5/8 by 30-1/2 by 33-7/16 inches. Mobility comes from two swivel casters paired with two rear wheels, a simpler arrangement than the five-caster layouts above: it rolls well in straight lines, but it does not glide sideways, so plan the path before the engine goes on. Four adjustable mounting arms cover the common bellhousing patterns in this weight class. The bright yellow finish is easy to spot in a dim garage and shows grime clearly, which makes wipe-downs and pre-use inspections simpler. For a first engine stand, or one that will be hung on a wall or slid under a bench between occasional projects, the low weight and small footprint are the argument here.

VEVOR Engine Stand, 1300 lbs (3/5 Ton) Rotating Engine Motor Stand with 360 Degree Adjustable Head, 4-Caster, 4 Adjustable Arms

The VEVOR 1300 carries the second-highest rating in this group at 1,300 lb, or 3/5 ton, which places it between the 1,250 lb mid-range stands and the 1,500 lb AT26801UR. That covers dressed small-block V8 engines and most V6 and inline-six work, with the mounting head adjusting through 360 degrees on four adjustable arms for common bellhousing patterns found on passenger-car engines.

Where this model differs from the other stands here is the base: a U-shaped layout rather than an H-frame or single post, widening the footprint under the load against the tipping moment of a rotated engine. The frame combines alloy steel with cast iron in the rotating hardware. It rolls on four universal casters, two of them fitted with brakes, so it can be repositioned around a project car and parked firmly on sloped concrete.

Listed dimensions are 36.2 by 27.6 by 36.6 inches, and the stand weighs 50.7 lb, mid-pack here. A 20-inch handle and six location holes handle rotation and locking. Choose it for near-top capacity without a folding frame, where the U-shaped base suits your floor space.

How to choose

Start with capacity, and be honest about what the engine weighs dressed, with intake, manifolds, flywheel and accessories still attached. A bare small-block and a fully dressed one are very different loads. Leave clear headroom between the dressed weight and the stated rating, because rotation shifts the load off-center and stresses the mounting plate in ways a static number does not capture.

Next, look at the base and casters. Wide bases resist tipping better than narrow single-leg designs when the engine is sideways. More swivel casters make a loaded stand easier to position; at least one braking caster or a set of wheel chocks keeps it from drifting on sloped concrete. Check how the head locks: fixed locking positions give repeatable angles, while a pin-and-hole head is fine if the spacing matches how you work. Folding frames are worth having if the stand shares space with a parked car. Finally, confirm the mounting arms can reach your bellhousing bolt pattern before ordering.

On safety history: no CPSC recall covers engine stands as a product class. The widely reported 2020 Harbor Freight recall involved jack stands, a different product that supports a raised vehicle rather than holding a removed engine, so do not let that headline steer this purchase either way. Still, check the exact model against the CPSC database before buying, and inspect welds, arms and casters before every use.

Who should skip

Skip this entire category if your work never separates the engine from the car: a stand only earns its floor space once a block is out. Also skip these five if your engines are heavy diesels or dressed big-blocks past the 1,500 lb ceiling of the strongest pick here; that work calls for a geared, shop-grade stand with a higher rating. And skip the stand-only purchase if you have no way to lift the engine onto it: a stand holds an engine but cannot remove one, so without a hoist or shop crane it is unusable on its own.

FAQ

What size engine stand do I need for a V8?

A bare small-block V8 typically falls inside a 1,000 lb rating, but a fully dressed engine with accessories can push well past it. For V8 work, the 1,250 lb class is the sensible floor and the 1,500 lb class adds real headroom for big-blocks and dressed engines. Match the rating to the dressed weight, not the bare block figure, and keep a margin rather than running at the limit.

Can an engine stay on a stand for months during a long rebuild?

Yes, that is a normal use, provided the stand sits on a level floor with casters braked or chocked and the engine is mounted with all four arms properly bolted. Recheck the mounting bolts after the first rotations, since settling can loosen them, and do not lean extra parts on the mounted engine, which adds load the rating never accounted for.

What is the difference between an engine stand and a jack stand?

They solve different problems. An engine stand bolts to a removed engine’s bellhousing and holds it on a rotating mount so it can be rebuilt at bench height. A jack stand is a static support placed under a raised vehicle to hold the vehicle’s weight while someone works beneath it. The two are not interchangeable, and the well-known jack stand recalls of recent years do not apply to engine stands.

Do I still need an engine hoist if I buy a stand?

Yes. The stand cannot lift an engine out of the engine bay or lower it in. Removal and installation require a hoist or shop crane, usually with a load leveler so the engine can be tilted as it clears the bay. The stand takes over once the engine is out, holding it at working height for teardown and assembly.

Final verdict

Match the stand to the heaviest dressed engine you expect to mount. The BIG RED AT26801UR is the default recommendation for most home garages: top capacity in this group, a folding frame and a stable H-shaped base. The TAM25671-2 and the ZLWBHBS cover the 1,250 lb middle ground, one with a tool tray and one with all-swivel cast iron casters. The W41025 wins on low weight and storage, and the VEVOR adds a U-shaped base and a 1,300 lb rating.

Product and ASIN Reference

Product ASIN
BIG RED AT26801UR Torin Steel Rotating Engine Stand, 3/4 Ton (1,500 lb), Blue B0BFDFZSQT
BIG RED TAM25671-2 Torin Steel Rotating Engine Stand, 5/8 Ton (1,250 lb), Red B0DNGMX2B9
ZLWBHBS 1250 lbs Engine Stand, Red B0FMRKDR2X
Performance Tool W41025 Rotating Vehicle Engine Block Stand, 1/2 Ton (1,000 lb), Yellow B001DKSQX4
VEVOR Engine Stand, 1300 lbs (3/5 Ton) Rotating Engine Motor Stand with 360 Degree Adjustable Head, 4-Caster, 4 Adjustable Arms B0BZTVNRMQ
A
Autozane Editorial Team
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.
Best Engine Stands: 5 Rotating Picks for Home…Check price on Amazon

More from Amazon

Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.

Amazon Prime

Free shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.

Start a Prime free trial
Audible

Audiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.

Try Audible free
Amazon Music Unlimited

Ad-free music streaming. Eligible new subscribers can start with a free trial.

Try Music Unlimited free
Amazon Business

A free business account with business pricing and bulk-buying tools for work, shop or home office.

Create a business account

As an Amazon Associate we earn from qualifying purchases.